Key takeaways
- Compare the best hand grip covers for fighters' strength work, from lifting grips and palm pads to thick-bar covers for deadlifts, rows and pull-ups.
Grip is the weak link in most fighters’ strength work. Deadlifts, heavy rows, farmer’s carries and high-rep pull-ups build the pulling power behind a strong clinch, solid takedown defense and hard grappling exchanges, yet the set often ends because the bar slips or a callus tears, not because the back and arms are done. A torn palm can also cost days of mat work. Hand grip covers solve that interface problem. They sit between your hand and the bar, or wrap around the bar itself, adding friction, spreading pressure and protecting skin so the target muscles become the limit again. This guide compares five proven styles, from strap-style lifting grips to thick-bar covers, for combat athletes who lift to fight better.
As an Amazon Associate, we earn from qualifying purchases.
Quick Answer
For most fighters, the Versa Gripps Pro is the best hand grip cover for heavy pulling, while the Cobra Grips PRO gives similar help with a rubber pad and padded wrist wrap. Bear KompleX carbon grips and JerkFit WODies protect palms during high-rep bar work, and Fat Gripz Pro covers thicken any bar for grip-focused training.
How to Choose
Start by separating three products that get mixed up. A grip strengthener is a squeezable trainer you crush in isolation to build grip strength, and this site covers those elsewhere. A hand grip cover is interface gear: something worn on the hand or fitted to the bar so you can hold heavier loads and protect your skin during real lifts. Full gym gloves are different again, covering the whole hand, trapping heat and often bunching on the bar. Covers leave the fingers free, go on and off in seconds, and keep a closer feel for the bar.
Within covers, there are three formats. Lifting grips pair a palm flap with a wrist strap, so part of the load transfers to the wrist; they suit deadlifts, rows and shrugs. Finger-hole palm grips, borrowed from gymnastics, mainly shield the palm from rips and add friction during pull-ups and other bar work. Bar covers slide over the bar itself and make it thicker, which trains grip harder rather than helping you hold on.
Fit decides whether a cover helps or annoys. Lifting grips usually size by wrist circumference, while palm grips size by hand length, often measured from the wrist to the base of the middle finger. Check the maker’s chart before ordering. Then look at material: rubber grabs well and wipes clean, leather breaks in and molds to the hand, carbon fiber resists stretching, and elastic fabrics trade some durability for comfort and wrist support. Finally, match the tool to your week. If torn calluses keep you off the mats, palm protection matters most. If your deadlift stalls because the bar rolls out of your fingers, start with lifting grips.
Versa Gripps Pro
The Versa Gripps Pro is the premium take on the lifting grip, and it is the pair to pick for heavy pulling days. A patented, self-supporting palm piece folds over the bar and locks in quickly, so setting up for a deadlift or row takes seconds instead of the wrapping routine of a traditional strap. The grip section is cut longer than standard, wrapping more of the bar for a secure hold, and the wrist strap is one and a half inches wide with high-density foam padding and a hook-and-loop closure that spreads the load across the wrist. Sizing follows wrist circumference across four sizes, and each pair is shaped for the left and right hand. They are made in the USA by Power Gripps. For fighters, the appeal is simple: your top sets of deadlifts, barbell rows and shrugs stop being grip tests, so the back and arms get the training effect you showed up for.
Specs
| Spec | Detail |
|---|---|
| Type | Lifting grip with padded wrist strap |
| Palm material | Proprietary non-slip material |
| Wrist strap | 1.5 in wide, foam padded, hook-and-loop closure |
| Sizing | By wrist circumference, four sizes from XS to XL |
| Origin | Made in the USA |
| Sold as | One pair |
Cobra Grips PRO
Cobra Grips PRO, from Grip Power Pads, covers the same job with a simpler build. A rubber palm pad sits against the bar and does the gripping, while an adjustable neoprene wrist wrap, padded for comfort, anchors the pad and shares the load. There are no finger holes and nothing to thread: you lay the pad over the bar, close your hand and lift. That speed matters in the strength circuits fighters often run, where you move between a pull, a carry and a press with little rest. The rubber surface also wipes clean after a session, which keeps gym-bag odor down. Cobra Grips work as an alternative to both lifting straps and lifting hooks for deadlifts, rows, shrugs and pull-ups, and the design is unisex. Choose them if you want the lifting-grip effect with fewer moving parts and an easier replacement when a pair eventually wears out.
Specs
| Spec | Detail |
|---|---|
| Type | Rubber grip pad with wrist wrap |
| Palm material | Rubber |
| Wrist support | Adjustable neoprene padded wrist wrap |
| Brand | Grip Power Pads |
| Best for | Deadlifts, rows, shrugs and pull-ups |
| Sold as | One pair |
Bear KompleX 3-Hole Carbon Hand Grips
Bear KompleX built its name on palm grips for high-rep bar work, and the 3-Hole Carbon model is the one that translates best to a fighter’s week. A carbon fiber palm panel covers the area where calluses form and tear, with three finger holes that keep it positioned during pull-ups, chest-to-bar work and kettlebell sessions. A wrist strap secures the grip so it stays put when you drop from the bar and go again. Carbon fiber resists stretching, so the panel keeps its shape instead of elongating the way soft leather can, and it works with or without chalk. For combat athletes, the value is skin insurance: the palm takes the friction instead of your hands, so a heavy pulling session on Monday does not leave you gripping a gi or a clinch with torn hands on Tuesday. Size from the maker’s hand-length chart.
Specs
| Spec | Detail |
|---|---|
| Type | Finger-hole palm grip |
| Palm material | Carbon fiber |
| Design | Three finger holes |
| Wrist closure | Wrist strap with hook-and-loop fastening |
| Best for | Pull-ups and high-rep bar work |
| Sold as | One pair |
JerkFit WODies
WODies combine two tools in one piece: a three-hole palm grip and a built-in wrist support wrap. The palm section protects against rips and blisters during pull-ups and bar work, while the long wrist wrap adds support that also helps on pressing movements, so one pair covers a full mixed session of pulls, presses and carries. The material is a latex-free elastic fabric, which feels softer against the skin than stiff leather and conforms as you open and close your hand. Because the wrist support is integrated, there is one less item to pack and nothing separate to lose in the gym bag. Fighters who split the week between strength work and conditioning circuits tend to like this format, since the same pair stays on for the whole session instead of being swapped between exercises. Follow the maker’s sizing guide, which is based on hand length.
Specs
| Spec | Detail |
|---|---|
| Type | Finger-hole palm grip with built-in wrist support |
| Palm material | Latex-free elastic fabric |
| Design | Three finger holes, integrated wrist wrap |
| Wrist support | Built-in wrap for pulling and pressing |
| Best for | Mixed sessions of bar work and lifting |
| Sold as | One pair |
Fat Gripz Pro
Fat Gripz Pro is the bar cover of this group, and it plays the opposite role from the other four. Instead of helping you hold on, a pair of dense sleeves slides over a barbell, dumbbell or pull-up bar and stretches its diameter to two and a quarter inches, turning standard equipment into a thick bar. Thick-bar work forces the hands and forearms to work far harder, building the crushing and supporting grip that carries over to clinch control, gi grips and holding an opponent’s wrists. The sleeves are made from a high-density compound that stays firm under load, and they fit standard-diameter bars and handles. Loads will drop sharply at first, which is normal and part of the training effect. Use them for a portion of your rows, curls, carries and pull-ups rather than every set, and keep the palm-protecting options above for your heaviest pulls.
Specs
| Spec | Detail |
|---|---|
| Type | Bar grip cover and thick-bar adapter |
| Outer diameter | 2.25 in |
| Material | High-density compound |
| Fits | Barbells, dumbbells, pull-up bars and cable handles |
| Best for | Grip and forearm strength work |
| Sold as | One pair |
Who Should Skip It
Skip grip covers if your coach is deliberately programming bare-hand grip development, since covering the hand removes part of that stimulus. Skip them for competition preparation in powerlifting, where grip aids are not allowed on the platform, and check the rulebook of any strength sport you enter. If you have a wrist injury that needs rigid support, these are training aids, not medical braces, so get assessed first. Bar covers are also the wrong buy if your gym already has thick bars, and palm grips are unnecessary if your pulling volume is low and simple callus care keeps your hands intact.
FAQ
Will using grip covers make my grip weaker?
Not if you use them with intent. Keep warm-up sets and dedicated grip work bare-handed, and bring the covers out for top sets, heavy pulls and high-rep bar work. Used that way, they protect skin and let the target muscles work harder, while your grip still gets trained.
What is the difference between lifting grips and palm grips?
Lifting grips use a wrist strap and a palm flap that folds over the bar, so the wrist shares the load; they are built for heavy deadlifts and rows. Palm grips are finger-hole protectors that mainly shield skin and add friction during pull-ups and other bar work.
Are hand grip covers allowed in competition?
Not on the powerlifting platform, where straps and grip aids are banned in competition lifts. Strongman rules vary by event and federation. In a normal gym session there is no restriction, but if you compete in any strength sport, check its rulebook before relying on covers in training.
How do I size and care for grip covers?
Lifting grips usually size by wrist circumference and palm grips by hand length, so measure and follow the maker’s chart rather than guessing. For care, wipe rubber and carbon panels down after training, let fabric and leather pairs air dry, and store them out of a damp gym bag.
Final Verdict
Match the cover to the problem. For heavy deadlifts and rows where the bar leaves your hands before your back is done, the Versa Gripps Pro is the strongest pick, with the Cobra Grips PRO close behind in a simpler rubber design. For palm protection across pull-up volume and mixed bar work, choose between the Bear KompleX carbon grips and the wrist-supporting JerkFit WODies. Add Fat Gripz Pro when the goal flips from holding on to building grip, and your strength work will support your fighting instead of stealing skin from it.
Product and ASIN Reference
| Product | ASIN |
|---|---|
| Versa Gripps Pro | B005XDIYDE |
| Cobra Grips PRO | B01BA0QDBI |
| Bear KompleX 3-Hole Carbon Hand Grips | B072L43PNN |
| JerkFit WODies | B00KKZJAJC |
| Fat Gripz Pro | B07QKML1SL |
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountAs an Amazon Associate we earn from qualifying purchases.






Write Your Review
No reviews yet. Be the first to share your experience!